Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
How must the saw blade be held after the cut is finished and before the blade
stops rotating?
a. | Release it to the up position. | c. | Raise 1" above the stock being
cut. | b. | Hold it in the down position. | d. | Pull to the out
position. |
|
|
2.
|
What special protection must be observed when using the motorized miter saw
outside?
a. | Keep the saw covered. | c. | Unplug the saw after each cut. | b. | Lubricate the saw
more often than normal. | d. | Connect the saw to a ground fault circuit
interrupter(GFCI). |
|
|
3.
|
How can the saw operator prevent the blade form binding when cutting warped,
bowed, or long stock?
a. | Clamp the stock to the table. | c. | Push the saw through the material
slowly. | b. | Hold the saw firmly. | d. | Hold the saw down securely after the cut is made. |
|
|
4.
|
When is it safe to remove wood scraps from the cutting zone on the motorized
miter saw?
a. | While the saw is positioned over material and ready for a cut to be
made. | c. | While the saw is off and the hand is not on the Off/On switch. | b. | While the saw blade
is clamped in the down position. | d. | While the blade is up. |
|
|
5.
|
Where should the saw blade be positioned when cutting is completed and the
operator is leaving the work zone?
a. | Up | c. | In its safest position | b. | Down | d. | Either a or b |
|
|
6.
|
Hands or fingers never come closer than __________ to the rotating blade when
operating the motorized miter saw.
a. | 2 inches | c. | 6 inches | b. | 4 inches | d. | 8 inches |
|
|
7.
|
What personal protection equipment should be worn by a motorized miter saw
operator?
a. | Hearing protection, eye protection and a dust mask | c. | Eye protection and hearing
protection | b. | Eye protection | d. | Hearing and eye protection, dust mask and gloves |
|
|
8.
|
The purpose of a trial cut before making the actual cut with the motorized miter
saw is to ____________ .
a. | see if the material is positioned correctly. | c. | see how the material will
cut. | b. | see if the saw is cutting properly and is set accurately. | d. | test the sharpness of the saw
blade. |
|
|
9.
|
Where should the saw blade be aligned when making a cut with the motorized miter
saw?
a. | Left side of the marking line | c. | Waste side of the marking
line | b. | Right side of the marking line | d. | On the marking
line |
|
|
10.
|
How should the saw blade be moved throughout the stock when making a cut with a
motorized miter saw that has a sliding arm?
a. | Push down, then pull out | c. | Pull out then push
down | b. | Push down | d. | Pull out, push down, then push forward |
|
|
11.
|
The purpose of a "stop" when making multiple cuts with the motorized
miter saw is to ____________ .
a. | hold the stock securely. | c. | reduce time required to make
cuts. | b. | improve cut accuracy and reduce time required to make cuts. | d. | get hands and fingers further away from the
cutting zone. |
|
|
12.
|
If a kickback should occur when a cut is being made the saw operator should
____________ .
a. | jump out of the way. | c. | raise the saw to the up position immediately. | b. | turn loose of the
saw immediately. | d. | hold the
saw firmly in the down position and release the On/Off switch. |
|
Matching
|
|
|
a. | Fence | i. | Turn Base | b. | Dust Bag | j. | Handle | c. | Table | k. | Vertical Holddown Vice | d. | Stationary Blade Guard | l. | Blade | e. | Miter Adjusting
Lever | m. | Arm | f. | Safety Start Button | n. | Retractable Blade Guard | g. | Miter
Scale | o. | Slide | h. | On/Off Switch | p. | Bevel Scale |
|
|
13.
|
#1
|
|
14.
|
#2
|
|
15.
|
#3
|
|
16.
|
#4
|
|
17.
|
#5
|
|
18.
|
#6
|
|
19.
|
#7
|
|
20.
|
#8
|
|
21.
|
#9
|
|
22.
|
#10
|
|
23.
|
#11
|
|
24.
|
#12
|
|
25.
|
#13
|
|
26.
|
#14
|
|
27.
|
#15
|
|
28.
|
#16
|