Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
A good grinding wheel will have a _________ sound
when it is “sounded”.
a. | dull | c. | ringing | b. | high
pitch | d. | low pitch |
|
|
2.
|
A fractured grinding wheel will have a _________
sound when it is “sounded”.
a. | dull | c. | ringing | b. | high
pitch | d. | low pitch |
|
|
3.
|
Grinding should be done only on the
__________.
a. | left side of the grinding wheel | c. | upper one-half of the grinding wheel | b. | right side of the grinding wheel | d. | lower one-half of
the grinding wheel |
|
|
4.
|
A grinder tool rest should never be more than _____
inch from the grinding wheel.
|
|
5.
|
When grinding, the operator should not stand
____________.
a. | in direct line with the grinding
wheel | c. | to the right side of the
grinder | b. | to the left side of the
grinder | d. | near the center line of the grinder |
|
|
6.
|
Grinding wheels which vibrate excessively do so
because ____________.
a. | they are out of round | c. | both a and b | b. | the arbor shaft of
the grinder is bent | d. | neither a nor b |
|
|
7.
|
The protective equipment item(s) which should be
used when truing a grinding wheel is/are _________.
a. | safety glasses | d. | all of
the above | b. | gloves | e. | a and c
above | c. | dust mask |
|
|
8.
|
If excessive pressure is applied to the grinding
wheel, it is likely to cause ________.
a. | a bent arbor | c. | an
overheated piece of metal | b. | a distorted piece
of metal | d. | a chipped grinding wheel |
|
|
9.
|
If the arbor revolutions per minute (RPM's) of
a given grinder is 3400, which grinding wheel would be safe for use on this particular
grinder?
a. | 1700 RPM grinding wheel | c. | 2800 RPM grinding wheel | b. | 2400 RPM grinding
wheel | d. | 4600 RPM grinding wheel |
|
|
10.
|
The spark deflector on a grinder should be adjusted
to within ____ inches of the grinding wheel.
|
|
11.
|
Before grinding, the operator should
_________.
a. | allow the grinder to reach full operating
speed | d. | a and b above | b. | make certain others are not standing in line with the grinding wheel
action | e. | a, b and c above | c. | clean the grinder
safety shields |
|
|
12.
|
Which of the following grinder wheels would cut the
fastest?
a. | Fine grit | c. | Course
grit | b. | Medium grit | d. | They would all cut
the same |
|
|
13.
|
A grinding wheel should be replaced when worn to
_____ of it’s original diameter.
|
|
14.
|
Which of the following grinding wheels would
produce the smoothest grinding surface?
a. | 30 grit | c. | 60
grit | b. | 40 grit | d. | 90
grit |
|
|
15.
|
The purpose of standing to the side when the
grinder is turned on is to ____________.
a. | to keep others out of the line of
work | c. | to make sure the grinder will come up to full operating
speed | b. | to keep from getting hit by flying
debris | d. | to make sure the wheel cover is on securely for the grinding operation to be
performed |
|
Matching
|
|
|
a. | Safety Shield | f. | Wheel Guard | b. | Plane Iron Grinding
Attachment | g. | Water
Pot | c. | Spark Deflector | h. | Motor | d. | Dust Chute | i. | Switch | e. | Tool
Rest | j. | Pedestal |
|
|
16.
|
#1
|
|
17.
|
#2
|
|
18.
|
#3
|
|
19.
|
#4
|
|
20.
|
#5
|
|
21.
|
#6
|
|
22.
|
#7
|
|
23.
|
#8
|
|
24.
|
#9
|
|
25.
|
#10
|