Multiple Choice
Identify the
choice that best completes the statement or answers the question.
|
|
|
1.
|
Material should be well supported when being cut
with the portable circular saw to _____________ .
a. | keep it from falling over | c. | so the cut can be made quickly | b. | to prevent binding the saw blade and causing a
kickback | d. | to prevent damaging the material |
|
|
|
2.
|
The saw blade should extend through the material
being cut by _______ inches.
|
|
|
3.
|
What personal protection safety equipment should be
worn by the portable circular saw operators?
a. | Safety glasses, hearing protection, and
respirator | c. | Safety glasses | b. | Safety glasses and hearing protection | d. | Safety glasses,
hearing protection, respirator, and gloves |
|
|
|
4.
|
Before putting the saw down after a cut has been
made ______________.
a. | unplug the saw | c. | make
sure the blade has stopped rotating | b. | make sure the
cover is over the blade | d. | all of these |
|
|
|
5.
|
To make a plunge cut with the portable circular saw
the operator should ___________.
a. | rest the front of the saw base on the material, uncover
the blade and slowly lower the blade into the material being cut. | c. | uncover the blade and slowly lower the saw blade into the material being
cut. | b. | lock the saw in stationary position, turn it on and
raise the material into the saw blade. | d. | rest the heel of
the saw base on the material, uncover the blade and slowly lower the blade into the material being
cut. |
|
|
|
6.
|
To make a long straight cut with the portable
circular saw ___________.
a. | move the saw slowly through the cut so it can be guided
straight. | c. | such cuts can not be made with a portable circular
saw. | b. | clamp a guide on the
material. | d. | move the saw rapidly through the cut. |
|
|
|
7.
|
If the saw operator over extends himself/herself
when cutting with the portable circular saw, what is likely to happen?
a. | Strain their arm. | c. | Break
the saw blade. | b. | Cut through the
power cord. | d. | Will get off-balance, fall and cause an
accident |
|
|
|
8.
|
What symptom will the saw operator notice when a
cut is make too fast with the portable circular saw?
a. | The saw blade Rpm's will
decrease. | c. | The saw blade will dull
rapidly. | b. | Saw dust chips will be large. | d. | The operational
noise made by the saw will increase. |
|
|
|
9.
|
When should a portable circular saw operator unplug
the saw?
a. | When changing saw blades | c. | When making adjustments to the saw. | b. | Both b and c | d. | After each cut |
|
|
|
10.
|
The blade on the portable circular saw should be
aligned ____________ when making a cut.
a. | 1/2 inch away from the marking
line | c. | on the waste side of the marking
line | b. | on the marking line | d. | 1/4 inch away from
the marking line |
|
Matching
|
|
|
a. | Handle | g. | Angle Scale | b. | Retractable Guard | h. | Tilt Lock Knob | c. | Trigger
Switch | i. | Rip Guide Lock
Knob | d. | Titlting Base | j. | Anti-Kickback Clutch | e. | Electrical Cord | k. | Guard Lift Handle | f. | Blade | l. | Guide
Knob |
|
|
|
11.
|
#11
|
|
|
12.
|
#6
|
|
|
13.
|
#8
|
|
|
14.
|
#3
|
|
|
15.
|
#1
|
|
|
16.
|
#4
|
|
|
17.
|
#9
|
|
|
18.
|
#5
|
|
|
19.
|
#7
|
|
|
20.
|
#12
|
|
|
21.
|
#10
|
|
|
22.
|
#2
|